Aadit Kannan · Electromechanical Engineer

About

I study Mechanical Engineering and EECS at UC Berkeley, and I am interested in robotics, semiconductors, and space.

Outside of work I lift weights, boulder, and love exploring the world, which I occasionally film with my drone.

Currently:

  • Designing the 588 V accumulator hardware and cooling system for Formula Electric at Berkeley
  • Researching beyond-CMOS memory and logic while building high-frequency pulse electronics in Ramesh Lab
  • Building a compact high-ratio Wolfrom gearbox for humanoid joints
  • Incoming Starship Launch Mechanisms Engineering Intern at SpaceX
  • Reading Lines and Glass's Principles and Applications of Ferroelectric and Related Materials

Education

University of California, BerkeleyExpected Dec 2028B.S. Mechanical Engineering, Minor in EECS | GPA: 3.6
  • Current: Mechanical Behavior of Materials, Thermodynamics, Circuits and Devices
  • Prior: Manufacturing and Design, Physics E&M/Mechanics, Linear Algebra, Python/MATLAB, Calc 1/2/3, Chem

Experience

SpaceXSpring 2027Starship Launch Mechanisms Engineering InternStarbase, TX
  • Starting Jan 2027 · Launch Mechanisms & Structures team
Formula Electric at BerkeleySep 2025 - PresentHV Battery Mechanical EngineerBerkeley, CA
  • Designed and optimized air-cooling architecture for a 420-cell accumulator, using MATLAB and transient ANSYS Icepak CFD to model airflow distribution, pressure losses, and thermal performance; predicted a 52.4 °C peak cell temperature over a 25-minute endurance run, 4.6 °C under the 57 °C target
  • Built analytical heat-transfer and fan-curve models predicting a 425 CFM, 521 Pa operating point with 79% of pressure loss across the cell bank; used measured vehicle data to identify a 39 A RMS no-fan limit at 35 °C ambient
  • Designed and manufactured high-voltage electronics packaging for a 588 V accumulator, integrating busbars, insulation, waterproofing, and serviceability; reduced enclosure mass by 18% and sized conductors for 80 A peak current
Ramesh Lab, UC BerkeleyJan 2026 - PresentUndergraduate ResearcherBerkeley, CA
  • Designed, fabricated, and characterized a 4-layer GaN FET pulse-generator PCB for beyond-CMOS thin-film devices, integrating 50-ohm routing, grounded BNC, Keithley instrumentation, and RP2040/Python control
  • Characterized switching and pulse response for pF-scale, high-resistance devices, achieving programmable pulses up to 30 V and down to 100 ns; identified the capacitance-limited return edge driving a 1 ns-class redesign
FIRST RoboticsAug 2021 - Aug 2025Hardware Lead (#13216) and Captain (#20424, #13215)Santa Clara, CA
  • Designed 5 competition robots in 500+ part CAD assemblies, using FEA to cut custom aluminum chassis mass
  • Won the Design Award three times for a counterbalance mechanism, a custom telescoping arm, and topology-optimized parts; led hardware design and manufacturing across 3 FTC teams
Posha, formerly NymbleJun 2023 - Aug 2023Engineering InternSan Francisco, CA
  • Designed, coded, and built a positioning fixture for the ingredient-dispensing mechanism; repaired and validated 20+ customer cooking robots by diagnosing electrical and mechanical failures across integrated subsystems

Selected Project

Wolfrom Robotic ActuatorMay 2026 - Present
  • Designed a 50.45:1 compound Wolfrom actuator for a humanoid elbow, integrating a MAD MC610 motor and ODrive controller in a 104 × 81 mm package; built a printed V1 that runs on the bench to prove fit and meshing
  • Eliminated two critical failure modes through ANSYS FEA and KISSsoft analysis ahead of metal fabrication: planet bearings overloaded at 50 Nm peak (static FoS 0.78), resolved with 6 mm needle-bearing pins raising static FoS to about 4, and carrier-tilt contact stress 50% above hand calculations, addressed with case-carburized gears
  • Modeled 88.5% forward / 87.3% backdriven mesh efficiency at 30 Nm in KISSsoft with no self-locking; dyno testing pending
  • Reduced simulated housing mass by 35% through topology optimization; applied DFMA in Onshape with tolerance stack-ups, lead-in chamfers for self-aligning single-direction assembly, and print orientation along load paths

Skills

Mechanical Design: SolidWorks/PDM, FEA (ANSYS), CFD (Icepak/Fluent), Onshape, KISSsoft, GD&T, DFM/DFA, Fusion 360

Electronics and Test: KiCad, LTspice, GPIB/SCPI, Keithley 2400, Oscilloscope

Manufacturing: CNC and Manual Mill/Lathe, CAM, TIG Welding, OMAX Waterjet, FabLight Laser Cutter, FDM/SLA, Moldflow

Software: MATLAB, Python, Java, Git